From top to bottom the new Windsor Executive Range offers features unavailable from other garage manufacturers.

What makes it so special?
The terracotta tiled effect roof offers stunning good looks designed to match traditional roof styles. All fascias and gutter boards are clad in white uPVC that requires no more than an occassional clean to keep them looking like new.

Genuine brick front pillars add character and blend easily into traditional surroundings, or if you prefer, both front pillars can be specified in Canterbury Spar finish.

The Windsor comes with Hörmann pre-finished white powder coated fully retractable steel horizontal up and over doors.

Also included as standard are black or white uPVC-guttering and a white 4 foot fixed uPVC double glazed window.

On completion of installation our fitters will apply a Unibond sand/cement fillet to the internal permiter base of the garage walls in order to help prevent leaks.

Specialist Roof

Exclusive to Lidget Concrete

For more information download the Lidget PDF: <Download Here> (PDF Document) (file size 852kb)

Standard Features

1) Roof panels supported on prime steel box section trusses for extra strength and rigidity
2) Timber roof runners 70 x 70mm, planed and treated closer pitched
3) uPVC clad fascias as standard
4) White Hormann horizontal rib, steel framed, powder coated, fully retractable up and over door
5) Sand and cement fillet to internal perimeter walls
6) Genuine brick front posts in either red or buff finish
7) Flush jointed concrete panels, mastic sealed and securely bolted
8) Panels steel reinforced for extra strength
9) Maintenance free white uPVC gutter boards
10) White uPVC, 4ft fixed window
11) Attractive maintenance free Canterbury Spar aggregate finished panels
12) Guttering in black or white maintenance free, half round 41/2 inch uPVC
13) Terracotta tile effect roof panels

Extra high apex roof suitable for 4 wheel drives, people carriers and vans.

Plastisol steel clad with roller shutter - up to 10ft clearance. Steel cladding and roller shutter doors available in various colours.

Remote controlled roller shutter doors.

For more information download the Lidget PDF: <Download Here> (PDF Document) (file size 365kb)

A selection of smaller buildings suitable for your garden are available.

These buildings are particularly suitable for locking up valuable garden equipment, toys or even running your own little cottage industry.

Our range of buildings is almost endless with both Pent and Apex roof types being available, with any number of door and window combinations to choose from.

As with all Lidget products these durable garden buildings are built without compromise to the highest standards, ensuring years of valuable service.

Please note, we do need good access from the road side and the intended site for the building. Please ensure to inform us of anything that may hinder this access, such as narrow gateways, gradients, steps, soft/uneven ground etc. Help us to help you.

For more information download the Lidget PDF: <Download Here> (PDF Document) (file size 452kb)

 

 

Concrete Base Requirements
Garages should only be erected upon a permanent concrete base of suitable thickness. We recommend a minimum of 4 inch thickness throughout. The base should be FLAT, LEVEL AND SQUARE, and at least 6 inch longer and 6 inch wider than the external dimensions of the garage to be supplied.

General
The ground surrounding the base should be lower than the base. If not, water will lay on the base and break through the sand and cement fillet and leak into your building. If the driveway slopes down towards the front of your building, you must put in a gulley to take any surface water away. We cannot guarantee the performance of your building unless a gulley has been fitted.

In order to check that your base will be laid square, measure out a 3-4-5 triangle (fig 1) before securing your timber shutters.

In order to give your timbers a final check prior to concreting, measure the diagonals which should be equal (fig 2). We would also advise you to use a reputable ready-mix concrete company who will also be able to tell you the amount of concrete required.

If you are close to an existing building or boundary wall, make sure that you allow for the overhang of the roof, i.e., flat roof garages 6 inch (150mm) on front and rear and 3 inch (75mm) both sides, apex roof 6 inch (150mm) front, rear and both sides. This does not include gutter width. (fig 3)

After your garage has been erected we strongly recommend that a sand & cement fillet be placed on the base to panel joint all around the inside (not outside) of the building to avoid ingress of water. We recommend a 3 part building sand to 1 part cement with Unibond (PVA) added to the mix (fig 4)

For more information download the Lidget PDF: <Download Here> (PDF Document) (file size 424kb)